Making printed candles

When I was looking for a way to make custom candles, I typed "candles custom" into YouTube and found this super neat technique!

 This photo was taken while the candles were still warm.

I've been making these for well over a year now and have finally somewhat perfected my technique.

So here's what you do:

Start with white or cream colored candles.  (I like the kinds with a really soft wax... the kind you can scratch easily.  The wax melts much more evenly, so spend a little more and buy the $12 candle instead of the $6 or cheaper brands.  I generally wait and buy mine at Hobby Lobby when they're half-off.)

You'll also need:

Plain white tissue paper

Scotch tape

Computer paper

Wax paper

Lay the candle down on a piece of computer paper and mark the candle's size.  Decide how long and wide you want the image to be.

Insert your chosen image into your word processor.  Adjust the Page Layout to match your paper (either Landscape or Profile).  Hold your computer paper with the candle size marking against the screen and adjust the Zoom until the page on the screen is the same width as the computer paper.

Okay.  Once that is done... resize your image until it fills your candle's size markings.

 With a new sheet of computer paper, you want to cut your tissue paper to a slightly larger size.  Check your tissue paper.  There is a lightly shiny side as well as a dull side.  You want the shiny side to be against your computer paper so your image will be printed on the dull side.  Fold over the edges and scotch tape the tissue paper onto the back of the computer paper.

Insert your paper tissue-side down into your printer (depending on your personal printer).

This is a good tutorial I found on YouTube.

Print your image onto the tissue paper.  I always allow mine to dry for a minute or two before messing with them.  Consider me paranoid.

Cut out your image while it's still attached to the computer paper.  It makes the tissue paper less-likely to tear.  Test it on your candle.  Trim and make adjustments as necessary, then the fun begins!

I use a regular old hair dryer with a concentrator nozzle for all of my candles.  Use HIGH heat and HIGH speed.

Lay your tissue and wax paper aside.  You won't need them for a few minutes.  Begin blowing your candle to warm the wax.  Continue warming until a slight moisture is barely visible on the surface of the wax.  This is not warm enough for the wax to bead or run, just lightly warm to the touch.  I can tell by how "oily" the candle feels to my fingers, but you'll be able to judge better with the more you do.

When the candle is sufficiently warm, add your trimmed tissue paper taking care to smooth out wrinkles and gently pull it taut around the candle.  Wrap your wax paper around the candle and begin blowing with your hair dryer.

As you heat the wax, the wax will melt and saturate the tissue paper and seemingly leave the printed image on the surface.  Be extremely leery of bubbles or wrinkles in your tissue paper as you work.  When the wax cools, wrinkles have always appeared on the surface of my candles.  With practice, I have been able to minimize their appearance, but unable to eliminate them completely.  Please, if anyone knows some trick to preventing them, please share your knowledge!

I like to start in the middle and work either to the right or the left.

This tutorial is the one I watched to develop my own technique.

If your image is designed to wrap the entire way around the candle, make sure one end is completely saturated with wax before working on the other side.

Once your tissue is completely saturated with wax, allow the candle to cool for several hours and then you're done!

It's during the cooling process that my tissue paper inevitably wrinkles.  If you know or figure out how to prevent this, PLEASE SHARE YOUR SECRET WITH ME!

This photo was taken once the candles were cool.  See the light wrinkling on the Juicy Couture one?

Please visit my website
www.AshleyGesslerSHD.com

A collar of my own making... for the pooch

We have a new dog. She's a 4yr old Miniature Schnauzer, and she is an absolute princess! Taking that into consideration, she deserves a collar to match her award winning personality. I typed in "rhinestone pink dog collar" into Google to see what it would come up with... this is what I stumbled across.

And I thought to myself... I can do that.

 So I went shopping: choke chain for $1 and 18 feet worth of pink ribbon for $2 from Walmart, a package of split rings for $2, a poodle charm for $3, and three large lobster clasps for $1.50 from Hobby Lobby.

I have less than $10 in this project and TONS of left-over materials for additional creations!

So we begin.

I measured the clasp and chain parts (including one of the large rings) alongside Phoebe's current collar.  I marked one link longer than I figured I would need (now, I am extremely grateful I did).  I had my husband cut the chain.

Now, with my newly-trimmed chain, I attached the clasp to one of the split rings and attached it to the end of the chain.

Next, I began weaving the ribbon through the chain.  Once I had woven through the entire length, I tied off the ribbon and melted the knot with a lighter.  Repeat on the other end.

Attach your chosen charm.

Easy as that!

 

Phoebe is getting a new collar from Santa for Christmas!

Please visit my website
www.AshleyGesslerSHD.com

When I feel a little kinky...

Some mornings I wake up and I just feel kinky...

What's a girl to do?

Here's an easy way to FORCE your hair to curl if it has a little natural wave but really doesn't curl on its own... but it doesn't like to go straight either... how irritating.

You'll need: Curling Cream, Gel, Mousse, Flexible Hairspray, and Tresemme Curl Locking Spray.

I use Curly Sexy Hair: Curling Creme, Garnier: Curl Shaping Spray, Tresemme: Flawless Curls Mousse, Dove: Extra Hold Hairspray (It claims to condition while you style. I don't know if this is true or not, but it certainly doesn't make my hair feel stiff and yucky!), and Tresemme: Curl Locking Spray.

Most any brands will do.  Use what works best for your hair.

The only one I strongly recommend sticking with is the Tresemme: Curl Locking Spray.  I've tried what seems like an infinite number of other brands and none of them work quite as well.  They either frizz my hair, or they get gummy and tacky feeling, or they generally don't smell good.

If it doesn't smell good, why waste your money?

Cream- roots to tips.

Gel- tips only.

Mousse- roots only.

1. Don't brush your hair after getting out of the shower!

2. Pull your hair down from under your towel and just lightly run your fingers through it.

3. Flip your head upside down and scrunch.

4. Spray Tresemme: Curl Locking Spray to one small section of your hair.  Start with the ends since they will dry first.  (The alcohol in the spray helps your hair dry faster so it will hold the shape you're forming with your fingers.)

5. Immediately squeeze the freshly sprayed section of hair with your hand and dry with your hair dryer (on HIGH heat and LOW speed) while supporting with your hand.

6. Repeat in small sections until all your hair is dry.

7. Once all your hair is dry, lightly mist with your flexible hairspray and continue to scrunch!

You're ready to style and go!

TIPS:

+Once a section of hair is dry, don't spray with the Curl Locking Spray.  It will cause the hair to frizz.

+Remember to constantly move your hair by flipping your head from side to side.  This helps prevent your hair from getting too stiff as it dries.

+Don't spray your entire head with the Curl Locking Spray!  It will cause your hair to dry straight instead of curly!  The secret is: one small section at a time.

Voila!

Curly hair!

Watch the full tutorial here:

Please visit my website
www.AshleyGesslerSHD.com

Building Me A Bench

I've been talking about it for forever...

A BENCH.

A bench that looks like a window seat..

A bench that looks like a window seat but also has a lift-lid for hidden storage.

A bench that looks like a window seat with a lift-lid that can also be used as seating at the dining room table.

A bench that looks like a window seat with a lift-lid that can be used at the dining room table... like the one I saw in Better Homes and Gardens and fell in LOVE with!

 

A bench like this!

Jason and I have been tossing ideas and sizes and design structures around for over a month now.  We finally settled on what we wanted and Jason started construction today!

 

Our lovely blank wall.

 

My bench is born!

The frame is 5 feet long, 20 inches deep, and 20 inches high.

 See all the messy toys?  That's what we're trying to hide.

 

The scariest moment was when Jason cut and pulled off the baseboard.

That's when things got really real.

I pulled pictures from when we were constructing out house to find out where the studs were so Jason knew where to place the nails.  (The pictures we took during construction have proven to be PRICELESS over the years!  If you build, be sure to take pictures of absolutely everything.  You'll thank me later!)

We used decorative corner trim pieces.

Once the frame was attached to the floor (using concrete anchors drilled directly into our concrete slab) and the wall (using 3.5" screws), Jason cut and attached bead board to the outside of the frame.  He then trimmed and nailed a baseboard.  We decided to use decorative trim pieces for the corners which turned out quite lovely.

We used wood filler for any holes, sanded, and we were ready to paint!

The last piece was the solid wood top.  Since we couldn't get our hands on a single piece of wood in the size we needed, Jason used two 1x12x6 pieces of wood, fused them in the middle, and routed the edges.  With a little sanding, it is now looking like it has been attached to our wall the entire time we have lived here!

Hinges will come later, but for now, it's still functional for sitting and it's hiding a great deal of clutter.

 Stain coming soon!

Please visit my website
www.AshleyGesslerSHD.com

Making a "canvas" print

I saw a company on Pinterest that would take a photo of your choice, place a poem on it, and print it on canvas for you.  It was pretty expensive to have it done, but I liked the idea...

... SO WHY NOT MAKE IT MYSELF?

Blurry picture- love but not useful

I have always loved this picture from our wedding day, but with it being blurry I never had a use for it until this project crossed my path.

I started with this raw picture.  In my photo editing program I trimmed it to 11 X 14 and added text to the image.  I decided to use our wedding vows instead of a poem because they have so much more meaning to us, and keep in mind that any picture will print slightly larger than the desired size so don't run your text up to the edge of the picture!  I sent the picture to be printed at Southerland's Photo so it would be the very best quality.  Plus, I would much rather give my business to a small business where the people actually care about the product they produce than some un-feeling chain company any day.

I purchased an 11 X 14 canvas and Mod Podge at Hobby Lobby.  I already had black acrylic paint, sponge brushes, and acrylic sealer from previous projects.

Finished project!  The blurry picture in the background really adds

to the beauty

Here's how I put it together:

(Super easy!)

1. Paint the edges and back of the canvas with black acrylic paint.  Canvas is porous so it took several coats.

2. Trim the picture to just inside the edges of the canvas so nothing hangs over.  My canvas was not perfectly square, so keep that in mind when you're trimming.

3. Use a black Sharpie to disguise the white edges of the printed photo.

4. Mod Podge the canvas face and apply your picture.  I flipped the canvas face-down and rubbed the back while the Mod Podge was drying so I got a nice flat picture without air bubbles.

5. Mod Podge the sides and front of the canvas.  Make sure to get the Mod Podge deep into the crevices along the edge of the print so nothing can catch on it and rip it off.  I did 3 coats (waiting about an hour between coats).

6. Spray with an acrylic sealer so it won't have that "tacky" feeling.

The white edge of the picture before disguising it with the Sharpie

Please visit my website
www.AshleyGesslerSHD.com

I can't believe it's NOT stained glass! {Part 5}

A painting we will go!

Wipe off any exposed guidelines (from the carbon paper of grease pencil) off the glass!

I like to start with a background color that will make me feel like I've accomplished something.  In this case, I started with the Cocoa Brown because nothing excites me more than seeing the morning sun shining through the first bits of "painted glass" even if that bit is nothing more than one 2" X 2" square.

For the SEMI SOLID areas like the 1 inch border around the entire window, I start at the top of my chosen section.  I sling the bottle one good time to ensure that all the paint is completely into the tip of the paint bottle.  AIR BUBBLES ARE NOT YOUR FRIEND and a pain to deal with, so I try to keep them from happening in the first place.  I squeeze out enough paint that it slightly oozes down the glass.

  Gently squeezing the bottle, I scrub the paint in small, smooth circles, making sure any air bubbles in the paint are immediately pressed out and popped as soon as they happen.  I move down that entire section.  When I'm nearing the bottom of the section, I stop squeezing the bottle and use what paint is already on the glass to move against the bottom leading strip until all the crevices are filled in and the paint is all relatively the same thickness.

If you see a mistake in the earlier portion of your section LEAVE IT ALONE.  The paint begins setting quickly and will become tacky within minutes.  You can always come back with a razor blade and peel off a section once the paint dries if it's absolutely necessary.

Wipe any excess paint off the leading strip and be careful not to accidentally touch the wet sections.

The SOLID AREAS, like the solid white sections in the middle of the window, use up a great deal of paint.  I used almost 4 bottles of Snow White paint just for the four large, white boxes.  I start by slinging the bottle so everything is in the tip and all the air is safely at the top of the bottle (VERY IMPORTANT!) before running a very thick line of paint at the top of my section... thick enough that the paint flows down the glass.  Instead of scrubbing the paint as I do for the Semi-Solid areas, I continue squeezing the bottle and adding more paint as I move further and further down.  You always want to make sure your bottle is being held so the paint will continue to flow into the tip uninterrupted!  Since you're not scrubbing the paint onto the glass, there are precious few chances to eradicate any air bubbles without leaving mark.

Once I near the bottom, I only gently squeeze the bottle and scrub in small circles to move the paint up against the leading strip.  If the paint is too thick at the bottom of the section it will roll over the leading strip and spill into the next section.  Keep in mind that gravity is at work here!

The DISTORTION AREAS are by far my favorite to paint.  It's like scribbling in sloppy cursive!  There really are no special tricks or tips... just have fun.  If the paint gets too thick, it will look more like a Semi-Solid section instead of a Distortion area, but play with it and figure out which look you prefer!

AND HERE IS THE FINISHED PROJECT!!!

 

Please visit my website
www.AshleyGesslerSHD.com

I can't believe it's NOT stained glass! {Part 4}

I drew out three different flower shapes that were all similar yet different at the same time and labeled them as such: Large, Small, and Wide.  These were the designs I traced directly onto the window to make my job a little easier.

Large, Small, and Wide flower stencils.

I leaded the strategically placed and traced flowers first.  Next, I leaded the leaves free-hand, connected the flowers with the lead vines, and created the "curlie-q's."  Leading free-handed is my favorite part because it's like drawing with very little room for error!

Every time I cut off extra leading strips, or reached the end of a strip and had a bit left over, I saved the pieces... even the tiny little shreds.  There were plenty of instances where I only needed a 1/4 inch piece and it would have been silly for me to start a whole new strip.

Save the left-over pieces of leading strips.

Lastly, I leaded the straight lines behind my flowers by following the lines I drew in {Part 2} with the carbon paper.  I used a ruler after the strip was placed to push it into a perfectly straight line (using my fingers made the lines look wavy).

I soldered all the joints with liquid leading which took me almost three days in and of itself because my hand kept cramping from squeezing the bottle.  And, "POOF!"  Here it is!  All leaded and ready to paint!

Completely leaded and ready to paint!

Please visit my website
www.AshleyGesslerSHD.com